Hardi has about 30% cellulose fiber in it and the rest is cement. Hardi shrinks after it is installed so you must keep it tight to the the next board and not leave expansion gaps on either side. It definitely must have slip sheets under the joints. It must be caulked at the corner posts and openings. If you cut it, it must be doped or painted as it is installed.
LP Smartside on the other hand expands after it is installed. Approximately 3/8 of an inch. horizontally for the length of each board. They have a gauge to place between each horizontal lap to allow for expansion. Here again I would use a slip sheet behnd the lap. Both prodcts are susceptible to moisture. So here again you must dope or paint any cuts as you install if you are using a predinished product. Both Hardi and LP require you to where masks to keep from breathing in the dust. Not good for your lungs.
If you really want a good product with a superior finish, consider steel siding. Vinyl is just plastic and it breaks when hit by hail requiring it be replaced. Get a grill any where close to it when barbeciung and it melts. Steel can dent in a major hailstorm, and it normally doesn't. but it still won't leak. Hardi board and LP will cost you more to install if prefinished than steel and steel is virtually maintenance free. My house has steel on it since 1975. Most vinyls will last unitil the next big hailstorm and then you have to replace. The one drawback for steel is, it is harder to repair than vinyl. but can be done by a skilled craftsmen, without removing the whole wall.
Direct added value to your home:
Finish out unfinished living areas
Upgrades to bathroom and kitchen
Add additional living area
All other items completed to home have negligible value added benifits in terms of Apprasial added value.
Hi Pamela,
There are many great door & window product lines to choose from. The most important consideration is the glass package and style. I recommend consulting with a few glass companies and door/window contractors to help with the decision. You need to choose your doors and windows based on location - cliamate zone. Marvin is top of the line, but it is extremely expensive, just like Renewal by Andersen. I recommend looking at Milgard, Jeld-Win and Andersen (not Renewal). Good Luck!
Gregg
Murray Lampert Design, Build, Remodel
www.murraylampert.com
You might want to look into AB2299 for the state of California. Add additional living area and raise the value 160k-400K to all R1 Properties. We build these for a living and are seeing a 2% return rate on your investment.
Set up includeing Dust Containment field, reverse air flow and floor protection
Demo concreete work, framing, roofing
Rough electrical
Rough plumbing
Inspection
Drywall,
Inspectioin
Mud and tape
Cabinets and fixtures
Tile backsplash
Finish electrical
Finish plumbing
Fixtures
Finishes Painting
Final Inspection
Clean up
Photo Pizza Party
Each phase should show labor (both in house and sub), materials broken out
Hope this helps
Philip Anderson
HDR Remodeling
Berkeley Ca
Adding the stylish furniture in home can be very effective in increasing the home vlaue.
Hi. Hardi is a siding made of painted cement board. SmartSide is a painted wood product. Both are rigid materials and stay perfectly straight on the house. Their drawbacks are very visible seams and both require painting after about 10 years.
A good way to add value to your house is to do home improvement. Many renovation and home additions add value to the house. Also, painting by interior painting San Jose is a good way to add value to the house. One of the simplest and most cost-effective improvement is house painting. Low-maintenance landscaping also adds value when you sell your house.
the most important thing you need to make sure you have is a highly rated low-e window. low -e will reflect the solar rays away from the inside of your home so it doesn't heat up during the summer or direct sun etc and during the winter it works in the opposite manor. winter it will keep the heat inside your home keeping your house comfortable. there are many good brands of windows like Andersen, Western, Hurd, Marvin, Eagle (andersen), just to make a few. be sure and do plenty of research and get estimates from. 4-5 companies and compare dont just get estimates from 1 or 2 companies. good luck.
The glass package and the insulation of the window are the most important. The best window would be quadriple or triple pane window with foamfilled sashes and krypton or argon gas inbetween the glass. The dense gas keeps the cold air out in the winter and the hot air out in the summer. The foam filled sashes keep the insulation like your walls. Also choose vinyl over wood for better insulation,
There are companies that offer energy evaluations and some even use thermal imaging and a tool / process called a blower door reading / test. This will help identify the cause and opportunities for correction. You can do some easy items as well like ensuring all like plate covers have insulated pads behind the covers, check for insulation around your homes perimeter if you have an unfinished basement, check your homes exterior for small gaps or holes left from old utilities and service work performed over the years. Best of luck!
Ugh, I totally feel your pain! We’re actually going through the same exact stress right now here in Sacramento. We were all ready to pull the trigger on the solar install, but then the contractor told us our old panel won’t pass code. It’s so frustrating because it feels like another huge expense that just pops up out of nowhere. We’re still debating if we really need to swap the whole electrical box out or if the guy is just trying to upsell us. Has anyone in the area dealt with this? Did you guys actually end up upgrading your stuff, or is it possible to get by with the existing setup?
Hardi™ is a fibre-cement product and the LP product is a chip-board/resin composite. The Hardi™ comes both finished and unfinished, the LP is unfinished and must be painted with a high quality exterior coating that meets the demands and longevity requirements of the region in which it is utilized. Finished Product warranties vary based on the above variables.
Honestly, don't skimp on this part. I had the exact same dilemma last year and decided to just get it done. If your setup is older, it’s not just a sales pitch—it's really about making sure the system handles the extra load safely so you aren't dealing with tripped breakers every time the AC kicks on. I ended up calling the guys for an electrical panel replacement Sacramento https://menderix.com/all-services/electrical/electrical-panel-upgrade/ and it was totally worth the peace of mind. Everything runs so smooth now, and the solar works perfectly without any glitches. Better to do it right once than to regret it later!